3.0mm Duplex Zipcord Pull-Proof Jacket PM FC Fiber Jumpers Single
Mode
1. Basic Introduction:
Polarization Maintaining (PM) Patch Cords come in many flexible
configurations, with the choice of connectors. SQS PM Patchcords
shows excellent environmental stability, high extinction ratio,
high return loss, and low polarization dependence.
A cost-effective solution that provides high bandwidth and
transmission rates over long distances. This high-quality multimode
fiber optic patch cable is specifically designed for ethernet
applications. Each connection has great durability and is resistant
to pulls, strains, and impacts during installation.
Our cables are 100% optically inspected and tested for insertion
loss before you receive them. A pull-proof jacket design surrounds
the Multimode, OM3, 62.5 fiber which is immune to electrical
interference.
FC connector is designed specifically with high turbulence
performance in mind; it features a unique "floating" ferrule that
makes vibrations irrelevant to fiber connections!
2. FC To FC Patch Cord Benefit & Features:
- Cable Diameter: 3.0mm duplex zip cord
- Low back reflection and insertion loss
- Premium quality UPC ceramic ferrule for best performance
- Pull-Proof Jacket
- Special ceramic ferrule, compatible with FC with narrow key
- High extinction ratio up to 35 dB/1550nm
- Wide wavelength range
- Low angle misalignment
- Combination with fiber arrays
3. Fiber Optic Patch Cord Applications:
- Sensors
- WDM systems, optical amplifiers
- Laboratory works
- Interferometric polarization modulators
- High bit rate telecommunications
4. Specification&Technology Parameter
| Parameters | Value |
| Connector Type | LC/UPC,LC/UPC |
| Center Wavelength(nm) | 1310 or 1550 |
| Max.Insertion Loss(dB) | 0.3 |
| Min.Extinction Ratio(dB) | 23 |
| Min.Return Loss(UPC) (dB) | 55 |
| Min.Return Loss(APC) (dB) | 65 |
| Key Orientation | Slow Axis |
| Axis Alignment(deg) | ±3 |
| Operating Temperature(℃) | -20~+70 |
| Storage Temperature(℃) | -40~+85 |
| FIber Type | PM Panda Fiber |
* For Device with connector.IL is 0.3dB higher,RL is 5dB lower,ER
is 2dB lower.
* The default connector key is aligned to the slow axis.
5. FC Connector Specification& Technology Parameter:
| Parameter | Unit | Index |
| End-Face Type | | PC | UPC | APC |
| IL | dB | SM: ≤0.3；MM ≤0.1 |
| Repeatability | dB | ≤0.1 |
| interchangeability | dB | ≤0.2 |
| RL | SM | dB | ≥50 | ≥55 | ≥65 |
| MM | dB | ≥36(Without APC connector) |
| Mating Times | | ＞1000 |
| Operating Temperature | ℃ | -40~ +80 |
6. Our Service:
Your patch cord selection is important to the type of fiber optic
network you are working on. Some are ideal for single-mode, while
others might be the right for a Multimode installation. Another
factor to consider is the polished type when using single-mode
cables.
While your patch cord choice is important, it is only one piece of
the fiber-optic network to choose from. Take a look at what's
available in these other key product categories:
7. Connector Type Abbreviations:
SC - a snap-in style connector. Known for its excellent
performance. Referred to as Subscriber Connectors, Square
Connectors, or Standard Connectors.
ST - a very popular choice connector for Multimode networks. Also
referred to as Straight Tip connectors, they utilize a
bayonet-style coupling type, enabling a simple twist-on and
twist-off installation.
FC - was at one time the most popular single-mode connector type,
but is now typically being replaced by SC and LC connectors. Also
known as Ferrule Connectors, they utilize a screw-on coupling type
to be used in high-vibration environments and are commonly used for
datacom, telecom, measurement equipment, and single-mode lasers.
LC - a small form factor connector—measuring half the size of an SC
connector. This is a popular choice for single-mode cables. Also
referred to as Lucent Connectors, Little Connectors, or Local
Connectors, these snap-in connectors are typically used for
high-density connections and are compatible with plug-and-play
devices such as SFP modules and XFP transceivers.
